
Keep the waste moving
Waste-to-Energy
Feed chutes, grates, slipstick conveyors and ash extractors
Pictured: Slipstick pans, ready to ship
01 The wear you're fighting
Municipal solid waste (MSW) arrives with glass, metal, grit and moisture in every load. In an energy-from-waste plant, that mix wears through feed chutes, grates, slipstick pans and ash extractors, and the trucks keep coming while you fix them.
You’ll find TASSCO steel in energy-from-waste plants, usually in the spots that used to fail first. We build liner systems and full weldments in house with domestic plate, matched to each wear zone and ready for your outage.
Where it wears first
- Feed chute and feed deck liners
- Grapple tines and flipper-lifter bars
- Slipstick conveyor pans
- Ash extractor rams and shear beams
- SDA cones and turning vanes
- Flyash elbows and screw flights
Impact and gouging at the feed
Grapples drop mixed MSW into the feed chute, where scrap metal, concrete and glass hit the liners and grind down the slope sides toward the grate. Feed decks and chute liners need a hard face that takes gouging and keeps refuse sliding.
Wet ash that corrodes as it wears
Bottom ash leaves the grate into a water-quenched extractor, then rides slipstick and drag conveyors as a wet, gritty, chloride-laden mix. Mild steel and even 304 stainless lose ground fast here, so these zones need a grade that handles abrasion and corrosion at once.
Push and shear in the ash extractor
The extractor ram pushes wet clinker and metal up the discharge ramp and past the shear beam every cycle. Rams, push liners and shear beams take impact and sliding wear together, so clad surfaces and complete rebuilds keep the extractor on line.
Fine flyash in the SDA and ash system
In the spray dryer absorber (SDA) and the flyash system, fine particles erode cones, turning vanes, elbows and dead boxes wherever the flow turns. A smooth overlay face holds up there and gives flyash less to build up on.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Ash extractors
- Complete ash extractor rebuilds
- Clad rams, shear beams and push liners
- Discharge doors, hinges and access panels
MSW feed and infeed
- Feed and infeed chute liners
- Incline and apron conveyor liners
- Feed deck and slope side liners
Grate and tines
- Grapple tine liners and tine bases
- Flipper-lifter bars
- Vibratory grizzly finger-deck liners
Slipstick conveyors
- Feed, intermediate and discharge pans
- Pan liners in XT and Fused Alloy
- Feed-end extension assemblies
Spray dryer absorber
- SDA wear packages
- Turning vane sets
- Outer cones
Ash and flyash handling
- Chutes and drag conveyors
- Screw conveyors and flighting
- Hardened piping and elbows
03 Right grade, right wear zone
The grades waste-to-energy customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
Fused Alloy
Fusion-bonded chromium carbide overlay
- SDA cones and slipstick pans
- Feed decks
CORRHARD
12% chromium martensitic stainless, 3/16″ to 1″
- Wet ash and flyash service
- Where 304 stainless gives up
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Clad elbows and dead boxes
- High-abrasion flow
Magna Tuff
Modular magnetic rubber liner system
- Same-day patch, no welding
- No hot work permit needed
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

Ash extractor weldment, built in house 
SDA outer cone
05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
Questions we hear
Waste-to-Energy wear questions
Want it all on two pages? Download the Waste-to-Energy guide (PDF).
What liner lasts longest on slipstick conveyor pans?
Plants use Fused Alloy on slipstick pans and feed decks. It's a fusion-bonded chromium carbide overlay with a smooth, bead-free face, and it runs about twice the life of welded CCO. We also build pan liners in TASSCO XT.
What wear plate holds up to wet ash better than 304 stainless?
CORRHARD, a 12% chromium martensitic stainless plate. It runs nearly twice the hardness of 304 with similar corrosion resistance, and it's rated for 3–5× the life of 304 stainless where abrasion and corrosion meet, as they do in wet ash and flyash service. Your shop welds it with standard 309L practice.
Can you rebuild an ash extractor for a waste-to-energy plant?
Yes. We do complete ash extractor rebuilds and full weldments in house with domestic plate, including clad rams, shear beams, push liners, discharge doors, hinges and access panels.
How do I patch a worn chute in an energy-from-waste plant without welding?
Magna Tuff modules are 40 Shore A rubber with rare-earth magnets built in, and they snap onto steel by hand. There's no welding and no hot work permit, so you can patch it the same day. They're rated for 170°F continuous, so use them away from hot ash.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.
More in power & energy

