
Ready before peak season
Asphalt
Dryer drums, cold feed bins, slat conveyors and silos
Pictured: Fused Alloy slat conveyor
01 The wear you're fighting
Paving season doesn't wait for a rebuild. The flights, slat decks, bins and chutes in your plant wear against hot aggregate and RAP all season, so the time to replace them is while the plant is cold.
You can have your plant ready before paving season starts. We measure the machine, match the grade to each wear zone from the cold feed bins to the load-out chute, and fabricate to your contours in our Birmingham shop.
Where it wears first
- Dryer flights and drum liners
- Drum throat liners and dryer sweeps
- Cold feed bin and RAP hopper liners
- Drag slat floors and sidewalls
- Silo cones and gate liners
- Loader bucket liners and cutting edges
Hot aggregate in the drum
Flights lift and veil aggregate through the burner's heat for every ton you make, and the drum throat and sweeps take the scrub as material enters and leaves. Flights cut from through-hardened plate hold their shape longer, so the veil stays even and the drum keeps drying.
Impact at the cold feed
Loaders drop aggregate and RAP into the bins from bucket height, and big RAP chunks hit hopper floors and belt impact plates hard. Those spots need thick, tough plate, and so do the aprons in your RAP crusher.
Sliding abrasion in the slat conveyor and silo
Hot mix drags across the slat deck floor and down through silo cones and gates all day. A hard overlay floor takes that steady drag, and a smooth face keeps the mix from building up on it.
Sticky RAP and fines that hang up
RAP carries binder that smears and packs in bins and transitions, and wet fines bridge in cold feed hoppers. A low-friction, bead-free face keeps material sliding, so you aren't sending someone in with a bar.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Dryer and drum mixer
- Veiling, spiral and combustion flights
- Formed and rolled drum liners, shell plates
- Drum throat liners and dryer sweeps
Cold feed and RAP
- Aggregate and RAP bin liners
- Hopper impact floors and transitions
- Feeder floors, belt impact plates, skirtboards
RAP crushing and screening
- Impact, cone and jaw crusher liners
- Impact housing and apron liners
- Punch plate decks: round, square or hex
Drag slat and bucket elevator
- Slat deck floor and sidewall liner sets
- D-link and drag chain bottom liners
- Elevator buckets
Batch tower, silos and baghouse
- Pug mill liners and mixing paddles
- Silo cone, transition and gate liners
- Diverter and pant-leg chutes
Loaders and weld-on armor
- Loader bucket liner sets and floor packages
- Cutting edges, including carbide faced
- Range Tuff bars, buttons, bolt protectors
03 Right grade, right wear zone
The grades asphalt customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
TASSCO HD
Heavy-gauge wear plate, 1¼″ to 5″
- Impact plate
- RAP crusher aprons
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Chutes
- Pan liners
Fused Alloy
Fusion-bonded chromium carbide overlay
- Slat deck floors
- Hopper and silo interiors
Range Tuff
High-chrome white iron weld-on wear parts
- Chocky bars, 1×1 up to 1×6
- Buttons 3″ to 6″, donut bolt protectors
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

XT dryer flights 
Fabricated hopper, ready to ship 
CORRHARD-lined hoppers
05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
What material should I use for asphalt dryer flights?
We build veiling, spiral and combustion flights from TASSCO XT. It's through-hardened to 477 BHN from face to centerline, so a flight keeps working as it wears down, and your shop welds it with standard procedure. It's stocked from 3/16″ to 1″.
How do I keep hot mix and RAP from sticking in a slat conveyor or silo?
Line the slat deck floor and the hopper and silo interiors with Fused Alloy. It's a fusion-bonded chromium carbide overlay with a smooth, bead-free face, at 0.33 CoF as produced against about 0.47 for welded overlay. A polished finish runs even lower and helps release sticky material.
What wear plate should I use in asphalt plant chutes?
Where material slides, COMP-C is a good fit for chutes and pan liners. It puts a 60 HRC chromium carbide face on a mild steel base your shop can form and weld. Where material lands hard, like impact plates and RAP crusher aprons, use through-hardened TASSCO HD.
Can I protect a loader bucket without rebuilding it?
Yes. Range Tuff chocky bars (1×1 up to 1×6), buttons (3″ to 6″) and donut bolt protectors are 700 BHN high-chrome white iron on a mild steel backer that welds straight onto your bucket. When a bar wears out, you replace the bar instead of the bucket.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.


