
For paving and milling contractors
Road Building Equipment
Milling machines, pavers, pickup machines and shuttle buggies
Pictured: Milling drum housing · Fused Alloy liners
01 The wear you're fighting
Your paving train only moves as fast as its slowest machine. Milling drums, paver floors and shuttle buggy conveyors wear hard on cut asphalt and hot mix, and a worn part on one machine stops the whole crew.
You’ll find TASSCO parts across the paving train, from the milling machine to the shuttle buggy to the paver. We match the grade to each surface and cut it to fit, so your crew keeps paving.
Where it wears first
- Milling drum housings and door skis
- Paver floor plates and auger flights
- Pickup machine cutting edges and floors
- Shuttle buggy hoppers and conveyor floors
Abrasion inside the milling drum
Cut asphalt and aggregate whip around the drum housing at speed and scour the liners and door skis from the inside. Those surfaces need a hard carbide face that takes that scrub shift after shift.
Hot mix sliding across the floor
Hot mix slides across paver floor plates and through the augers on every load. Heat and sharp aggregate wear floors and flights together, and a hard, even face keeps material feeding evenly.
Impact at the truck dump
Trucks drop full loads into shuttle buggy and paver hoppers. The impact zones and conveyor transfer points take the first hit, and weld-on spot armor protects them without rebuilding the whole section.
Sticky material and buildup
Asphalt grabs rough, beaded surfaces and builds up on pickup floors and inside drum housings. A smooth, bead-free overlay gives it less to hold onto, so material keeps moving and cleanup goes quicker.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Milling machines
- Drum housing liners in COMP-C or Fused Alloy
- Hydraulic door skis
- Booth and debris containment liners
Asphalt pavers
- Paver floor plates in XT or COMP-C
- Auger flights in COMP-C
Asphalt pickup machines
- Cutting edges in XT
- Floor plates in XT or Fused Alloy
Shuttle buggies (MTV)
- Hopper liners for the truck dump zone
- Conveyor bed and floor plates, all three stages
- Range Tuff spot armor in high-impact zones
03 Right grade, right wear zone
The grades road building equipment customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Drum housings and door skis
- Paver floor plates and auger flights
Fused Alloy
Fusion-bonded chromium carbide overlay
- Drum housings and booth liners
- Pickup floors
Range Tuff
High-chrome white iron weld-on wear parts
- Hopper and conveyor spot armor
- Bucket faces
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

COMP-C paver floor plates 
Fused Alloy pickup floor 
COMP-C milling machine ski 
Range Tuff buttons and bars in service
05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
Questions we hear
Road Building Equipment wear questions
Want it all on two pages? Download the Road Building Equipment guide (PDF).
What should I line a milling machine drum housing with?
Chromium carbide overlay. COMP-C goes on drum housings and hydraulic door skis, with a 60 HRC carbide face on a mild steel base your shop can form and weld. Fused Alloy also lines drum housings and booth liners, with a smooth, bead-free face that gives material less to grab.
What wear plate works for asphalt paver floor plates?
Paver floor plates run in TASSCO XT or COMP-C. XT is through-hardened, 450–514 BHN across the full section, and we cut it to fit your machine. COMP-C is built for heavy sliding abrasion and goes on auger flights too.
How do I protect a shuttle buggy hopper and conveyor?
Line the hopper in the truck dump zone and the conveyor bed and floor plates in all three stages, then add Range Tuff spot armor where material hits first. Range Tuff is 700 BHN high-chrome white iron on a mild steel backer that stitch welds straight onto your existing steel.
Can you cut floor plates and edges to fit my machine?
Yes. Send us your drawing or a worn part, and we'll cut floor plates, cutting edges and liners to fit in our Birmingham shop.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.
More in equipment & bulk handling

