From the mining face to the product warehouse

Potash Mining

Feeder breakers, skips, mills, dryers and chutes

Pictured: CORRHARD-lined hoppers

01 The wear you're fighting

Potash ore is abrasive, and the brine that comes with it is corrosive. From the feeder breaker to the warehouse reclaim, your liners fight both, and the dryer and compaction circuit adds a fine, dry product that has to keep flowing.

Conventional or solution mine, tell us where the wear shows up first and we’ll start there. We match the grade to wet or dry service and build each liner in our Birmingham shop.

Where it wears first

  • Feeder breaker and continuous miner liners
  • Ore passes and skip loading pockets
  • Scrubber and attrition cell liners
  • Brine launders and thickener sumps
  • Dryer flights and compactor chutes
  • Railcar and truck load-out chutes
  • Brine in the mill

    Scrubbing, flotation and thickening all run wet with brine. Launders, troughs and sump liners lose metal to corrosion and abrasion together, so a stainless wear plate outlasts carbon steel there.

  • Impact at the face and the breaker

    Continuous miners, feeder breakers and ore passes take the first hit from run-of-mine ore. In those dry impact zones, heavy through-hardened plate takes repeated hits without cracking.

  • Sliding wear after the dryer

    Once product leaves the dryer, it's dry, fine and abrasive. Dryer chutes, compactor feed chutes and flake breaker liners see steady sliding wear, which is where a chromium carbide overlay pays off.

  • Product that has to keep flowing

    Finished potash can build up on rough plate and weld beads, and a hung-up product chute holds up load-out. A smooth, bead-free face keeps it moving from the screen deck to the railcar.

02 What TASSCO builds

Built off your spare set, or measured on the machine

  • Underground mining

    • Continuous miner and feeder breaker liners
    • Panel belt transfer and loading pocket liners
    • Ore pass liners and impact plates
  • Shaft and hoisting

    • Skip loading pocket liners and guides
    • Skip bucket wear liners
    • Headframe chutes and dump points
  • Crushing and grinding

    • Crusher and impactor housing liners
    • Rod mill feed and discharge chutes
    • Scrubber and attrition cell liners
  • Flotation and wet processing

    • Brine and slurry launders and troughs
    • Thickener feed and sump liners
    • Wet screen deck frames and liners
  • Drying and compaction

    • Rotary dryer flights and chutes
    • Compactor feed chutes and flake breaker liners
    • Product screen decks and hoppers
  • Storage and load-out

    • Warehouse reclaim feeders and chutes
    • Railcar and truck load-out chutes
    • Loader bucket liners and cutting edges

04 Shop-built, field-proven

  • Fabricated screw conveyor sitting in its trough
    Screw conveyor and trough
  • Fabricated transition chute built in the TASSCO shop
    Fabricated transition chute
  • Set of fabricated lifter flights for a rotary dryer
    Rotary dryer lifter flights

05 · How we work

One supplier, one number to call

  1. Measure

    Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.

  2. Draw

    Grade, thickness, holes and bends. Kept on file for next time.

  3. Fabricate

    Cut, formed, rolled, beveled and drilled in our Birmingham shop.

  4. Deliver

    Marked and kitted for the changeout, ready to bolt up or weld in.

Questions we hear

Potash Mining wear questions

Want it all on two pages? Download the Potash Mining guide (PDF).

What liner material resists brine corrosion in a potash mill?

CORRHARD. It's a 12% chromium martensitic stainless with corrosion resistance similar to 304 at nearly twice the hardness, and it runs 3–5× the life of 304 in brine, slurry and flotation zones.

What wear plate should I use on feeder breakers and crusher walls?

TASSCO HD. It's through-hardened in heavy sections from 1¼″ to 5″, every plate is Brinell-tested, and it keeps its toughness down to −50°F. In dry impact zones, it takes repeated hits without cracking.

How should I line dryer and compactor chutes?

COMP-C is the usual pick there. It's a chromium carbide overlay welded to a mild steel base, with a hard, carbide-rich face for heavy sliding wear in dry areas. For product chutes where flow is critical, Fused Alloy's smooth, bead-free face gives potash nothing to hang on.

Can my shop weld CORRHARD liners?

Yes. CORRHARD welds with standard 309L practice. It's magnetic, so don't substitute it where 304 runs beneath a magnet.

Let's talk

Tell us what's wearing out. We'll have your back.

Call us or send a note below. You'll hear back from a real person, fast.

(205) 949-2725