
Keep the mixers turning
Concrete Products
Mixers, block machines, batch plants and yard iron
Pictured: Fused Alloy pan mixer liner set
01 The wear you're fighting
Concrete is sand and stone carried in wet paste, and it grinds on every mixer floor, paddle and chute it touches. When a mixer goes down, your pour schedule goes with it.
You’ll get liner sets, paddles and scrapers built to your mixer model and bolt pattern, cut and fabricated in our Birmingham shop. Tell us the machine, and we’ll match the grade to each wear zone.
Where it wears first
- Pan and planetary mixer floor liners
- Mixer paddles and wall scrapers
- Twin shaft paddles and door liners
- Block machine feedbox liners
- Batch plant chute liners
- Loader bucket liners and cutting edges
Wet abrasion inside the mixer
Every batch drives sand, stone and cement paste across the mixer floor and walls under the paddles. That's steady, wet sliding abrasion, and it's where a fused carbide floor earns its place.
Paddles and scrapers at the leading edge
Paddles and scrapers push through the full mix on every turn, so their faces and edges wear first. Weld-on white iron on scraper faces and bolt heads protects the part you'd otherwise replace.
Buildup that steals capacity
Concrete that sets on a rough liner or weld bead grows layer by layer until the mixer or chute holds less and takes longer to clean. Smooth, bead-free faces in mixers and batch plant chutes give paste less to hold onto.
Impact in recycled concrete crushing
Crushing returned and demolition concrete puts heavy impact on impact crusher plates and jaw cheek liners. Thick, through-hardened plate takes those hits without cracking, and it works on cutting edges and drag plates in the yard too.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Precast pan and planetary mixers
- Mixer floor liners and paddles
- Inside and outside scrapers
- Inside and outside wall housing liners
Twin shaft mixers and batch plants
- Twin shaft paddles
- Mixer door liners
- Batch plant chute liner segments
Block and paver machines
- Feedbox liners and side liners
- Vibrating table rails
- Top plates, turntables, apron and shift plates
Pipe and precast
- Slurry pump inlets and spools
- Rolled wall liners
- Bucket elevator discharge chutes
Ready mix and yard
- Drum mixing paddles
- Slat conveyor floor and side liners
- Loader bucket liners and cutting edges
Recycled concrete crushing
- Impact crusher wear plates and liners
- Jaw crusher cheek liner sets
- Track plant skirt liners, floor plates and punch plates
03 Right grade, right wear zone
The grades concrete products customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
Fused Alloy
Fusion-bonded chromium carbide overlay
- Mixer floor and wall liners
- Batch plant chute liners
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Chute liner segments
- Sliding wear in bins and hoppers
TASSCO HD
Heavy-gauge wear plate, 1¼″ to 5″
- Impact crusher wear plates
- Cutting edges and drag plates
Range Tuff
High-chrome white iron weld-on wear parts
- Mixer wall scraper faces
- Edge and bolt-head protection
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

Fused Alloy floor in a precast pan mixer 
Precast mixer wall scrapers, Range Tuff faced 
Ready mix drum mixing paddle
05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
Questions we hear
Concrete Products wear questions
Want it all on two pages? Download the Concrete Products guide (PDF).
What liner lasts longest in a pan or planetary concrete mixer?
We line mixer floors and walls with Fused Alloy. It's a 700 BHN chromium carbide layer fused to a mild steel base, with about twice the service life of welded overlay. The face is smooth and bead-free, so concrete has less to stick to.
Can you make liners and paddles for my mixer model?
Yes. We build liner sets, paddles and scrapers to your mixer model and bolt pattern. Send us a drawing or a worn part, and we'll cut and fabricate the set in our Birmingham shop.
How do I protect mixer scrapers and bolt heads?
Range Tuff puts 700 BHN high-chrome white iron on a mild steel backer that stitch-welds onto your scraper. Range Tuff donuts cover the bolt heads on bolt-on liners, so the liner comes off cleanly when it's time to change it.
What wear plate should I use on a recycled concrete crusher?
TASSCO HD fits impact crusher wear plates. It's through-hardened to 450 BHN in thick sections from 1¼″ to 5″, with the toughness to take repeated hard hits without cracking or warping. It also makes good cutting edges and drag plates.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.


