
From the face to the load-out
Surface & Underground Mining
Shovels, loaders, haul trucks, crushers and ore passes
Pictured: P&H rope shovel dipper · 1¼″ Fused Alloy floor
01 The wear you're fighting
Every ton you mine has to get past a dipper, a truck box, a crusher and a string of chutes before it pays. When one of those parts wears through, the whole operation waits on it, whether you're in an open pit or running ore up a shaft.
Open pit or underground, tell us where the wear shows up first and we’ll start there. We measure the part or scan it, match the grade to each zone, and build it in our Birmingham shop.
Where it wears first
- Dipper and dragline bucket floors
- Haul truck box drop zones and tails
- LHD buckets and feeder breakers
- Ore passes and skip loading pockets
- Crusher liners and wear rings
- Transfer chutes above and below ground
Impact at the face and the dump
Shot rock loads into a dipper and drops into a truck box from the full height of the boom. Underground, ore falls the length of an ore pass before it hits the impact plates and the skip loading pocket. Those zones need thick, through-hardened plate that takes the hit without cracking.
Gouging in buckets and boxes
Dipper floors, dragline buckets, LHD buckets and truck tails all have rock dragged across them under load. A dense carbide overlay holds up to that gouging and sliding, and heavy wear strips and skis protect the edges that take the first contact.
Wet ore in the concentrator
Once ore reaches the mill, chutes, launders and tailings lines carry it wet. Carbon plate loses metal to rust and wear at the same time there, so a stainless wear plate built for both keeps those liners in service longer.
Tight access underground
Feeder breakers, underground transfer chutes and skip pockets sit where getting a part in is half the job. Liners cut and formed from a field measurement or scan fit the first time, so the change-out stays inside the shift you planned for it.
2:1
In the field
Fused Alloy service life compared with welded chromium carbide overlay in sliding abrasion.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Shovels and draglines
- Electric rope shovel dipper packages
- Dragline bucket floor and wall packages
- Hydraulic shovel skis and HD wear strips
Loaders and haul trucks
- Wheel loader bucket liner sets
- Haul truck box packages: floor, side, tail
- XT or HD in drop zones, COMP-C in tails
Crushing
- Cone crusher main frame liners and wear rings
- Impact crusher apron plates
- HD wear bar and ring sets
Feeders, pockets and surge bins
- Feeder wall liners and side skirts
- Reclaim pocket and rock box liners
- Primary surge pocket liners
Concentrator and mill
- Fine ore bin discharge chute liners
- Ball and rod mill trommel screens
- Rod mill and ball mill feed chutes
Conveyors, fans and load-out
- Tripper and transfer chutes
- Fan housing and blade liners
- Drop chute redesigns with DEM modeling
03 Right grade, right wear zone
The grades surface & underground mining customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
TASSCO HD
Heavy-gauge wear plate, 1¼″ to 5″
- Shovel skis and wear strips, 2″ and 4″
- Wear bar and ring sets
Fused Alloy
Fusion-bonded chromium carbide overlay
- Dipper floors, 1¼″ lining
- Dragline bucket floors
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Truck box tails
- Rolled bucket liners
CORRHARD
12% chromium martensitic stainless, 3/16″ to 1″
- Wet concentrator chutes
- Slurry and tailings handling
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

CAT shovel bucket, 2″ and 4″ HD 
CAT 994K bucket, 1″ Fused Alloy liner 
Field service scanning inside a fan housing
Precision Flow · Engineered transfer chutes
Steady flow, less dust, longer belts
Precision Flow fixes the transfer points that plug, spill, throw dust or chew up belts. We scan the chute, model your material with DEM, and redesign it so the stream lands centered and at belt speed. You see it work in the model before we cut any steel.


05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
Questions we hear
Surface & Underground Mining wear questions
Want it all on two pages? Download the Surface & Underground Mining guide (PDF).
What liner lasts longest in a rope shovel dipper floor?
Most mines line dipper floors with 1¼″ Fused Alloy. It's a fusion-bonded chromium carbide overlay with a 700 BHN surface and about twice the service life of welded overlay in sliding abrasion. Dragline bucket floors get the same treatment.
What wear plate holds up in LHD buckets and feeder breakers underground?
Where rock hits hard, TASSCO HD is the usual pick. It's through-hardened in heavy sections from 1¼″ to 5″ and keeps its toughness down to −50°F, so it takes repeated hits without cracking. Where rock mostly slides across the bucket floor, a chromium carbide overlay like COMP-C or Fused Alloy usually lasts longer.
How do I keep ore passes and transfer chutes from wearing through or plugging?
Put thick, through-hardened TASSCO HD where ore lands and Fused Alloy where it slides, since its bead-free face gives material nothing to hang on. If a chute keeps plugging or wearing in the same spot, Precision Flow models the flow with DEM and redesigns the chute before any steel is cut.
Which liner should I use in wet concentrator chutes?
CORRHARD. It's a 12% chromium martensitic stainless with nearly twice the hardness of 304 and similar corrosion resistance, and it runs 3–5× the life of 304 stainless where corrosion and abrasion are both present. It's magnetic, so don't use it where 304 runs beneath a magnet.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.
More in mining & minerals
Other industries we serve

Aggregate & Quarry
Crushers, feeders, screens, loaders and haul trucks
Learn more →
Coal Mining & Preparation
Rotary breakers, vessels, screens, bins and chutes
Learn more →
Salt Mining
Feeders, crushers, skips, conveyors and chutes
Learn more →
Potash Mining
Feeder breakers, skips, mills, dryers and chutes
Learn more →
Roofing Granules
Loaders, crushers, dryers, kilns and coloring plants
Learn more →