
From the cupola to the cleaning room
Foundry
Shakeouts, sand systems, blast and cleaning equipment
Pictured: Slag shaker pan set
01 The wear you're fighting
Foundry sand is silica, and it grinds on everything from the shakeout to the sand mixer. Add hot castings, slag and dust, and the pans, liners and wheels in your plant earn their keep every shift.
You’ll get liner sets, pans and fabricated wear parts for melt, shakeout, sand and cleaning. We work off your drawing or your worn part, match the grade to the zone, and build it in our Birmingham shop.
Where it wears first
- Shaker conveyor and slag shaker pans
- Coke bin bottoms and feeder liners
- Sand aerator wheels and mixer bottoms
- Rotary blast screen drums
- Cyclones and dust collection pipe
Impact at shakeout
Castings and molds drop onto shaker decks and pans, then vibrate along them for the length of the conveyor. The impact zones need thick, tough plate, and the pan floors need it heavy.
Silica sand that never stops sliding
Return sand is sharp and abrasive, and it scours shaker pan liners, mixer bottoms, plow tables and conveyor transfers all shift. Chromium carbide overlay holds up to that steady sliding wear.
Heat from castings, slag and the melt
Hot castings, slag and cupola dust keep melt and shakeout equipment running warm. We match the grade to each zone and keep rubber liners on the cooler sections of the line.
Dust that wears through ductwork
Sand fines moving at speed cut through cyclones, elbows and dust augers from the inside. Hardened pipe and cyclones built to your line keep the collection system pulling.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Melt and charge
- Coke bin bottoms and coke transfer pans
- Metallics and coke feeder liners
- Cupola dust augers
Shakeout and casting cooling
- Slag shaker pan sets
- Shaker conveyor pan liner sets
- Deck rider wear bars
Sorting and cleaning
- Rotary blast screen drums and augers
- Pick and sort pans and deck plates
- Grinding and press table tops
Sand system
- Sand aerator wheels, built and balanced
- Mixer bottoms and V-paddle plates
- Plow tables for sand conveyors
Dust collection and air
- Cyclone assemblies with skimmer box
- Cyclone replacements built to your line
- Induction-hardened pipe and elbows
Yard and repair
- Loader bucket liners
- Magna Tuff patches on running lines
- Hardfacing and joining wire
03 Right grade, right wear zone
The grades foundry customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
TASSCO HD
Heavy-gauge wear plate, 1¼″ to 5″
- Shaker deck impact zones
- Heavy pan floors
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Slag shaker pans
- Shaker pan liners
Magna Tuff
Modular magnetic rubber liner system
- Patches on running lines
- No hot work permit needed
Range Tuff
High-chrome white iron weld-on wear parts
- Aerator wheel rod ends
- Edge and impact armor
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

Sand aerator wheel, Range Tuff rod ends 
Fabricated hopper, ready to ship
05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
What wear liner should I use on a foundry shaker conveyor?
Use TASSCO HD in shaker deck impact zones and on heavy pan floors. It's through-hardened to 450 BHN in sections from 1¼″ to 5″ and takes repeated hard hits without cracking or warping. Where sand slides, line slag shaker pans and pan liners with COMP-C, a 60 HRC chromium carbide overlay.
Can you rebuild sand aerator wheels?
Yes. We build and balance sand aerator wheels and face the rod ends with Range Tuff, a 700 BHN high-chrome white iron on a weldable mild steel backer.
How do I patch a worn pan or pipe without shutting down the line?
Magna Tuff modules are rubber with rare-earth magnets built in, so one person snaps them on by hand with no welding and no hot work permit. They're rated for 170°F continuous and 200°F short-term, so use them away from hot castings and the melt.
Can you build parts from my worn part instead of a drawing?
Yes. We work off your drawing or your worn part, match the grade to the wear zone, and build it in our Birmingham shop.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.


