
From the log yard to the boiler
Biomass & Wood Pellets
Dryers, hammermills, pellet mills and fuel handling
Pictured: XT cyclone, Fused Alloy target plates
01 The wear you're fighting
Bark, grit and sand ride in with every load of wood fiber, and they wear through dryer flights, hammermill liners, screws and chutes around the clock. In a pellet plant or biomass power station, one worn-through part can stop the whole line.
Send us a drawing or your worn part, and we’ll build the replacement in Birmingham with the grade matched to each wear zone, from the chip screen to the load-out chute.
Where it wears first
- Chip screen decks and scalping discs
- Rotary dryer flights and drum liners
- Hammermill liners and breaker plates
- Cyclone target plates and elbows
- Drag conveyor floors and screws
Grit and moisture at the green end
Logs and residuals carry dirt and sand from the yard into debarkers, chippers and chip screens. That grit makes wet green fiber surprisingly abrasive in in-feed chutes and screws, and the moisture adds corrosion on top.
Heat and tumbling in the dryer
Rotary dryer flights lift and drop fiber through hot gas for the full length of the drum, so they wear from sliding abrasion at temperature. Flights and drum liners need plate that keeps its shape through heat cycles.
Fast-moving fiber in grinding and air
Dry hammermills and pneumatic lines move fiber at speed. Hammermill housings, breaker plates, cyclone target plates and wear-back elbows take the hit where the flow turns, and that's where chromium carbide overlay pays for itself.
Buildup and combustible dust
Fines pack onto rough surfaces in chutes and drag floors, and combustible dust turns every welding job into a planned event. A smooth, bead-free liner keeps fiber moving, and Magna Tuff patches install by hand with no hot work, which matters anywhere dust collects.
02 What TASSCO builds
Built off your spare set, or measured on the machine
Log yard and chipping
- Debarker and chipper in-feed chutes
- Chip screen decks and scalping discs
- Log deck and transfer liners
Green fiber and drying
- Rotary dryer flights and drum liners
- Dryer in-feed and discharge screws
- Green hammermill housing liners
Dry grinding and air
- Dry hammermill liners and breaker plates
- Cyclones, target plates, wear-back elbows
- Rotary airlock and diverter liners
Pelleting and cooling
- Pellet mill feeder and conditioner liners
- Pellet cooler and screener liners
- Fines return screws and troughs
Storage and load-out
- Silo discharge cones, live-bottom liners
- Railcar, truck and ship load-out chutes
- Drag conveyor floor and side liners
Biomass power
- Fuel reclaim screws and drag chain liners
- Boiler feed chutes and metering bins
- Ash drag conveyor and screw liners
03 Right grade, right wear zone
The grades biomass & wood pellets customers run
Every grade ships from stock as plate, cut to size, or fully fabricated. Every TASSCO product works here; these are the ones matched to your wear zones.
Fused Alloy
Fusion-bonded chromium carbide overlay
- Chutes and drag floors where fiber must keep moving
- Cyclone target plates
COMP-C
Welded chromium carbide overlay, 3/8″ to 1½″
- Hammermill liners and screws
- High-abrasion flow
CORRHARD
12% chromium martensitic stainless, 3/16″ to 1″
- Wet green fiber and ash service
- Where 304 stainless gives up
Magna Tuff
Modular magnetic rubber liner system
- Running-line patches
- No hot work near combustible dust
Flagship grade · Melted and made in USA
TASSCO XT
Hard from face to centerline, consistent from heat to heat, and your shop welds it with standard procedure. Stocked 3/16″ to 1″.
04 Shop-built, field-proven

XT bark scalping discs 
Drag chain conveyor, built in house 
Rotary dryer lifter flights
05 · How we work
One supplier, one number to call
Measure
Off your spare set, off the machine, or with LiDAR scanning and DEM modeling.
Draw
Grade, thickness, holes and bends. Kept on file for next time.
Fabricate
Cut, formed, rolled, beveled and drilled in our Birmingham shop.
Deliver
Marked and kitted for the changeout, ready to bolt up or weld in.
Questions we hear
Biomass & Wood Pellets wear questions
Want it all on two pages? Download the Biomass & Wood Pellets guide (PDF).
What's the best wear liner for a wood pellet hammermill?
Most plants run COMP-C in hammermill liners and screws. It's a 60 HRC chromium carbide overlay welded to a mild steel base, so you get a hard face for sliding abrasion and a base your shop can form and weld with conventional practice.
How do I keep wood fiber from building up in chutes and drag conveyors?
Line them with Fused Alloy. Its smooth, bead-free face runs 0.33 CoF as produced, against about 0.47 for welded CCO, so fiber has less to grab. Plants also use it for cyclone target plates.
Can I patch a worn chute in a pellet plant without hot work?
Yes. Magna Tuff modules are 40 Shore A rubber with rare-earth magnets built in. One person installs them by hand with no welding, no fasteners and no hot work, which matters around combustible dust. They're rated for 170°F continuous, so keep them away from dryer heat.
What plate holds up to wet green fiber and ash?
CORRHARD, a 12% chromium martensitic stainless plate. It runs nearly twice the hardness of 304 with similar corrosion resistance, so it keeps going in wet green fiber and ash service where 304 stainless gives up.

Let's talk
Tell us what's wearing out. We'll have your back.
Call us or send a note below. You'll hear back from a real person, fast.
More in power & energy

